Traditional ECG monitors usually require a carry-on monitor to be placed close to the patient's neck or wrist pocket, and the noise and interference of the wireless ECG monitor is greatly reduced, and the size can be reduced to even the back of the electrode. Provides more accurate signals than traditional solutions. This circuit is inexpensive and provides a diagnostic quality 1 lead ECG trace that eliminates the need for a 60 Hz notch filter. All circuits can be worn in the clothes, so patient comfort and privacy are greatly improved.
The patient's monitoring data is encrypted and automatically uploaded to the on-site collection and analysis system in the hospital, nursing facility or maintenance facility every few minutes. The patient can upload information to the doctor's office or clinic at a predetermined time (daily or weekly) without removing the monitor or repositioning the electrodes. The wireless ECG monitor can also be equipped with a memory card for data transfer via a mobile phone or LAN. In addition to performance, reliability, low power consumption, and cost, the wireless ECG monitor design must support a dedicated telemetry band so that the monitor's ECG data can be quickly, accurately, and safely transmitted to the data collector for evaluation.
Overview
In North America, the Wireless Medical Telemetry Service (WMTS) band and other unlicensed industrial, scientific, and medical (ISM) bands provide dedicated spectrum to ensure uninterrupted, reliable connectivity for data transmission. ADI's ADF7021 high-performance, narrowband ISM transceiver IC supports the WMTS band and the ISM bands of 433 MHz, 868 MHz and 915 MHz. The ADF7021 offers best-in-class receiver sensitivity, -123 dBm at 1 kbps, built-in T/R switch, VCO tank, RF/IF filter, fully automated automatic frequency control (AFC) and automatic gain control (AGC) Circuit. To extend battery life, the ADF7021 can be placed in a very low power sleep mode, reducing current consumption to less than 0.1 μA. When used with a low-power microcontroller, the ADF7021 has an average standby current of less than 2 μA. The WMTS-optimized radio station reference design (EVAL-ADF7021DBZ6) includes schematics and layouts that can be used as a reference for wireless ECG monitor design.
The wireless Holter monitor is extremely small enough to fit on the back of the ECG electrode, because it greatly reduces noise and interference, and its signal accuracy is superior to traditional designs. The circuit is inexpensive and provides a diagnostic-grade single-lead ECG. A 60 Hz notch filter is not required due to the presence of the drive legs. The transceiver (ADF702x shown below) and its peripheral circuitry vary with the frequency band in which it is used. Since all circuits can be worn in clothing, patient comfort and privacy are greatly enhanced.
Functional block diagram
AD623 is a single-supply integrated instrumentation amplifier, rail-to-rail output swing and low power consumption (3 V voltage power consumption 1.5 mW). Its central node is used to access the residual common mode signal.
Details: AD623 integrated single-supply instrumentation amplifier
The AD8500 low-power, high-precision CMOS op amp has a maximum supply current of 1 μA, a maximum bias voltage of 1 mV, a typical input offset current of 1 pA, rail-to-rail input and output, and a single 1.8 V to 5.5 V supply or Dual supply from ±0.9 V to ±2.75 V.
Details: AD8500 Low Power, High Precision CMOS Operational Amplifier
The AD8641 low power, rail-to-rail output junction field effect transistor (JFET) amplifier features high input impedance, high precision performance, and low cost with an input impedance greater than 681 kΩ.
Details: AD8641 Low Power, Rail-to-Rail Output Junction Field Effect Transistor
The AD7466 is a 12-bit ADC in a small package with very low power consumption and consumes 480 μW at 3.6 V/50 kSPS. It is available in a 6-lead SOT-23 package. For designs that require a wider dynamic range and higher signal-to-noise ratio, the AD7685 PulSAR® ADC provides 16-bit resolution and consumes 1.35 mW at 2.5 V/100 kSPS with 3 mm &TImes; mm QFN (LFCSP) package.
Details: AD7466 12-bit ADC
Another solution to achieve this signal chain is to replace the ADC and MCU with the ADuC7022. The functional block diagram is as follows. ADuC7022 built 16-bit / 32-bit MCU, which integrates a high performance 1 MSPS ADC is on a single chip. The ADC provides the necessary dynamic range to meet medical standards and detects weak ECG waveform changes. The ARM7 architecture includes a 32-bit register that enables real-time FIR filtering of ECG signals.
Functional block diagram
The ADuC70xx family is a fully integrated 1 MSPS, 12-bit data acquisition system that integrates a high-performance multi-channel ADC, 16-bit/32-bit MCU, and flash/EE memory in a single chip.
Details: ADuC7022: Precision Analog Microcontroller
Mini PC
Are you tired on big and messy wires on traditional computer tower? If yes, mini pc bring clean and space saving working environment back to you. Whatever daily tasks, like browsing web pages, documents checking or making, online teaching or learning, entertainments, etc. Or heavy duty handling, like photshops, video or music editing, gaming, apps developing, engineering drawing, designing jobs, etc. You can always find a right pc mini intel at this store.
Mini PC Office is an most and popular series designed for those who mainly run WPS, photoshops, PR, email, entertainments, etc. Sometimes, also call it as mini pc officeworks or home assistant mini pc.
Mini Gaming PC comes with higher level processors, like intel i3, i5, i7 10th, 11th or 12th; bigger memory and storage, like 16GB or 32GB ram, 512gb up to 1tb. Of course, rich slots support linking with two or more monitors or devices.
Except mini pc windows 11, there are also All In One PC , Student Laptop, Gaming Laptop , Android Tablet, Yoga Laptop , etc.
Mini PC Windows 11,High Performance Mini PC,Mini PC DDR4,PC Mini Intel
Henan Shuyi Electronics Co., Ltd. , https://www.shuyicustomlaptop.com