![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
1. Numerical relationship between shape tolerance and dimensional tolerance
When the dimensional tolerance accuracy is determined, the shape tolerance has an appropriate value corresponding to the shape tolerance value of about 50% dimensional tolerance value; about 20% dimensional tolerance value of the instrument industry as the shape tolerance value; heavy industry A 70% dimensional tolerance value is used as the shape tolerance value. This can be seen. The higher the dimensional tolerance accuracy, the smaller the shape tolerance is the smaller the dimensional tolerance ratio. When designing the dimensioning and shape tolerance requirements, except for special cases, when the dimensional accuracy is determined, the 50% dimensional tolerance value is generally used as the shape tolerance value. This is beneficial both to manufacturing and to ensuring quality.
2. Numerical relationship between shape tolerance and position tolerance
There is also a relationship between shape tolerance and position tolerance. From the formation of the error, the shape error is caused by machine vibration, tool vibration, spindle runout, etc.; the position error is due to the non-parallel of the machine guide rails, the tool clamping is not parallel or non-vertical, the clamping force acts, etc. Caused by the definition of the tolerance band, the position error is the shape error of the surface to be measured. If the parallelity error contains the flatness error, the position error is much larger than the shape error. Therefore, in the general case, when no further requirements are given, the position tolerance is given and the shape tolerance is no longer given. When there are special requirements, the shape and position tolerance requirements can be marked at the same time, but the shape tolerance value of the label should be less than the position tolerance value marked. Otherwise, the parts cannot be manufactured according to the design requirements during production.
3. Relationship between shape tolerance and surface roughness
Although there is no direct relationship between shape error and surface roughness in terms of numerical values ​​and measurement, there is a certain proportional relationship between the two under certain processing conditions. According to experimental research, the surface roughness accounts for shape tolerance in general accuracy. 1/5 to 1/4. It can be seen that in order to ensure the shape tolerance, the maximum allowable value of the corresponding surface roughness height parameter should be appropriately limited.
In general, tolerance values ​​between dimensional tolerances, shape tolerances, position tolerances, and surface roughness have the following relationship: dimensional tolerances > position tolerances > shape tolerances > surface roughness height parameters
From the numerical relationship between size, shape and surface roughness, it is not difficult to see that the numerical relationship of the three should be coordinated and coordinated during design. When the tolerance value is marked on the pattern, the roughness value of the same surface should be less than The shape tolerance value; and the shape tolerance value should be less than its position tolerance value; the position difference should be less than its dimensional tolerance value. Otherwise, it will cause trouble to the manufacturing. However, the most involved in the design work is how to deal with the relationship between dimensional tolerance and surface roughness and the relationship between various matching precision and surface roughness.
In general, it is determined by the following relationship:
1. When the shape tolerance is 60% of the dimensional tolerance (medium relative geometric accuracy), Ra≤0.05IT;
2. When the shape tolerance is 40% of the dimensional tolerance (higher relative geometric accuracy), Ra≤0.025IT;
3. When the shape tolerance is 25% of the dimensional tolerance (high relative geometric accuracy), Ra≤0.012IT;
4. When the shape tolerance is less than 25% of the dimensional tolerance (super high relative geometric accuracy), Ra ≤ 0.15Tf (shape tolerance value).
The simplest reference value: the dimensional tolerance is 3-4 times the roughness, which is the most economical.
Second, the choice of geometric tolerance1. Selection of geometric tolerance items
The functions of the integrated control project should be fully utilized to reduce the geometric tolerance items given in the drawings and the corresponding geometric error detection items.
Under the premise of meeting the functional requirements, the project with simple measurement should be selected. For example, coaxial tolerances are often replaced by radial circle runout tolerances or radial circle runout tolerances. However, it should be noted that the radial circle runout is a combination of the coaxiality error and the cylindrical surface shape error. Therefore, when it is replaced, the jitter tolerance value given should be slightly larger than the coaxiality tolerance value, otherwise it will be too strict.
2. Choice of tolerance principle
The function of the tolerance and the feasibility and economy of adopting the tolerance principle should be fully utilized according to the functional requirements of the measured elements.
The principle of independence is used for dimensional accuracy and shape accuracy accuracy requirements are large, need to meet the requirements separately, or the two are not connected, to ensure motion accuracy, sealing, no tolerances and other occasions.
Inclusion requirements are primarily used where rigorous assurance of the nature of the fit is required.
The largest entity is required for the central element and is typically used where the fitting requirements are assemblable (no mating requirements).
The minimum physical requirements are primarily used where it is necessary to ensure part strength and minimum wall thickness.
The reversible requirement is combined with the maximum (minimum) entity requirement, which makes full use of the tolerance zone, expands the range of the actual size of the measured component, and improves the efficiency. Can be used without affecting the performance.
3. Selection of benchmark elements
(1) Selection of reference parts
1) Select the joint surface where the parts are positioned in the machine as the reference part. For example, the bottom plane and side of the case, the axis of the disk part, the support journal or the support hole of the rotary part, and the like.
2) The reference element should have sufficient size and rigidity to ensure stable and reliable positioning. For example, combining two or more axes that are further apart into a common reference axis is more stable than a reference axis.
3) Select a more precise surface as the reference part.
4) Make the assembly, processing and testing benchmarks as uniform as possible. In this way, the error caused by the non-uniformity of the reference can be eliminated, and the design and manufacture of the jig and the measuring tool can be simplified, and the measurement is convenient.
(2) Determination of the number of benchmarks
In general, the number of references should be determined based on the orientation of the tolerance project and the positioning geometry requirements. Most of the orientation tolerances are for one datum, while the positioning tolerance requires one or more datums. For example, for parallelism, perpendicularity, and coaxiality tolerance items, only one plane or one axis is generally used as the reference element; for the positional tolerance item, the positional accuracy of the hole system needs to be determined, and two or three may be used. Benchmark elements.
(3) Arrangement of the benchmark order
When two or more reference elements are selected, the order of the reference elements is clarified and written in the tolerance grid in the first, second, and third order. The first reference element is the primary and the second reference element is the second. .
4, the choice of geometric tolerance values
General principle: Select the most economical tolerance value while meeting the function of the part.
According to the functional requirements of the parts, considering the economics of the machining and the structure and rigidity of the parts, the tolerance values ​​of the elements are determined according to the table. And consider the following factors:
The shape tolerance given by the same element should be less than the position tolerance value;
The shape tolerance value of a cylindrical part (except for the straightness of the axis) should be less than its dimensional tolerance value; if it is on the same plane, the flatness tolerance value should be less than the parallelism tolerance value of the plane to the reference.
The parallelism tolerance value should be less than its corresponding distance tolerance value.
Approximate proportional relationship between surface roughness and shape tolerance: Generally, the Ra value of the surface roughness can be taken as the shape tolerance value (20% to 25%).
For the following cases, taking into account the difficulty of processing and the influence of other factors besides the main parameters, in order to meet the requirements of the function of the parts, appropriately reduce the selection of 1 to 2:
a hole relative to the shaft;
Slim, relatively large shafts and holes; larger shafts and holes;
a larger part (greater than 1/2 length) of the surface of the part;
Line-to-line and line-to-face parallelism, perpendicularity tolerances with respect to face to face.
5, the shape of the no-tolerance provisions
In order to simplify the drawing, the shape and position accuracy can be guaranteed by the general machine tool processing, and it is not necessary to inject the geometrical tolerance on the pattern. The shape and the unfilled tolerance are executed according to the provisions of GB/T1184-1996. The general contents are as follows:
(1) Three tolerance classes of H, K, and L are specified for unmarked straightness, flatness, verticality, symmetry, and circular runout.
(2) The unroundedness tolerance value is equal to the diameter tolerance value, but cannot be greater than the unfilled tolerance value of the radial circle runout.
(3) The cylindricity tolerance value is not specified, and is controlled by the roundness tolerance of the element, the straightness of the prime line, and the injection or unfilled tolerance of the parallelism of the relative prime line.
(4) The unparallelism tolerance value is equal to the larger of the dimensional tolerance between the measured element and the reference element and the shape tolerance of the measured element (straightness or flatness), and takes two The longer of the elements is used as a benchmark.
(5) The unconformity coaxiality tolerance value is not specified. If necessary, the unfilled tolerance value of the coaxiality is equal to the unfilled tolerance of the circular runout.
(6) The tolerance values ​​of unlined contour, surface profile, inclination, and position are controlled by the injection or unfilled linear dimension tolerance or angular tolerance of each element.
(7) The un-noted full-bounce tolerance value is not specified.
6, the pattern representation of the shape of the unfilled tolerance value
If the unfilled tolerance value specified in GB/T1184-1996 is used, the standard and grade code shall be indicated in the title column or technical requirements.
: "GB/T1184-K".
The working tolerances of the “Tolerance Principle according to GB/T 4249†are not marked on the drawings and shall be carried out in accordance with the requirements of “GB/T 1800.2-1998â€.
Product catagories of stylus pen for ipad, which is just for iPad Versions 2018 & 2019 and above.
It can work on following:
iPad 6th 2018: A1893/A1954
iPad 7th 2019: A2197/A2198/A2200
iPad 8th 2020: A2270/A2428/A2429/A2430
iPad air 3rd: A2152/A2153/A2154/A2123
iPad Air 4th: A2072/A2316/A2324/2325
iPad mini 5th: A2124/A2125/A2126/A2133
iPad Pro 1st/2nd 11: A1980/A2013/A1934/A1979/A2228/A2068/A2230/A2231
iPad Pro 3rd/4th 12.9: A2069/A2229/A2233/A2232/A1876/A2014/A1895/A1983
Stylus Pen For Ipad,Stylus Pen,Stylus Pen For Drawing,Touch Pencil
Shenzhen Ruidian Technology CO., Ltd , https://www.wisonen.com